Portes Françaises en Fibre de Verre

Les portes françaises en fibre de verre Fibertec sont des portes battantes utilisables comme portes d'entrée ou comme portes de patio. Les portes françaises en fibre de verre ont l'avantage d'être facilement personnalisées, grâce à une large sélection de vitrages, croisillons, couleurs, finitions et fenêtres fixes latérales. Avec à votre disposition une liste interminable d'options esthétiques pour personnaliser vos portes en fibre de verre, vous obtenez des produits qui allient beauté et efficacité énergétique. Que vous soyez à la recherche d'une porte de patio en fibre de verre à très grande efficacité énergétique ou une porte d'entrée en fibre de verre élégante, les portes françaises en fibre de verre de la gamme 200 sont parfaites. Un fini en bois massif est également disponible en option. Les portes sont proposées avec le choix d'un battant en fibre de verre s'ouvrant vers l'intérieur, ou un battant en fibre de verre s'ouvrant vers l'extérieur. Toutes sont faciles à utiliser et parfaitement sûres.


SPECIFICATIONS(Click detail button on the side to open each menu)

Uses built in flush glazing bead, and can accept any standard size door lite glass. This optional slab style eliminates the traditional bulky door lite glass frame.
6 1/2” Pultruded fiberglass Frame filled with wood reinforcement, injection moulded reinforced mechanical welded corners with Polyurethane foam fill and sealed with silicone sealant. An optional 4 1/2” Pultruded Fiberglass Frame is available for single doors only. Door slabs are reinforced Fiberglass skin, available in woodgrain (beige) flush or embossed pattern. Door slab stile rails use weather resistant composite material.
Nominal slab sizes are 30” (certain styles only), 32”, 34”, and 36” wide by 80” height and 96” height. Fibertec manufactures to sizes specified + / – 1/8” (3.17 mm) industry tolerance.
Products have been independently tested and rated by AAMA, and NFRC (see energy ratings).
The inswing door system that has a thermally broken aluminum sill that is strategically placed for the drainage of water. The outswing door system uses a combination of aluminum and oak sill with q-lon weather stripping to ensure a positive seal to the slab.

Fibertec uses a multi-point licking mechanism for all of our fiberglass entry doors. The locking system allows for the latchbolts to throw 20 mm and are secured to prevent them from being forced back. The deadbolts are engaged by turning the key/knob, the top and bottom latchbolts act as well and as a result it becomes a 3 deadbolts locking system.

Advatntages of Multi-point Locking

fiberglass doors
  1. No lifting of handle is needed to engage locking points
  2. Provides great amount of security against forced entry
  3. Prevents air infiltration from gasket
  4. Protects door panel from warping
Optional Multipoint lock system by Ferco, is available in polished brass, antique brass, polished chrome, brushed chrome, and oil rub. This provides added security compared to traditional lock systems. It is highly recommended to use the Multipoint lock system on all 8’ height doors. Please see our hardware section for different handle styles for our fiberglass entry doors.
Fibertec uses a Pultruded Fiberglass Frame with a standard White finish using Sequoia TM series V advanced acrylic polyurethane (water borne) baked onto the finish. The finish is rated environmentally friendly due to its low VOC (Volatile organic compound). Fiberglass door slabs come standard unfinished, but is ready to prime and paint or stain (wood grain). Custom colours are available.
Occasional cleaning of glass and frame components with a non-abrasive detergent is recommended.
Shall be performed by experienced installers in accordance with manufacturer instructions and CSA A440.4 standards. Window shall be plumb and square after installation is complete and sealed to both interior and exterior wall with high quality sealant around the perimeter of the frame. If perimeter cavity is to be foamed, additional anchorage may be required to prevent bowing. It shall be the responsibility of the installers to make all necessary final adjustments to ensure normal and smooth operation.